1. Антоненко Л. П., Білан А. Д., Бутмарчук Т. А. Складанний Д. М. Вплив катіонованих крохмалів на целюлозне волокно // УПАКОВКА, 2010. – №2. – С. 22-24.
З метою вивчення впливу катіонних клеїв на утримування дрібного волокна на сітці досліджували вплив крохмальних клеїв КУ-1 та КД-2, які були отримані в лабораторії кафедри Е та ТРП НТУУ «КПІ», на целюлозне волокно з листяної деревини. Отримані результати свідчать, що ці клеї дають змогу отримати відливки з показниками, які значно перевищують показники відливків, отриманих з використанням клею Жуковського, та не поступаються зразкам виготовленим з клеєм церезан.
With the aim of investigation of cation glues’ influence on shallow fiber retaining on the net, the influence of starch glues such as КУ-1 and КД-2 received in the laboratories of E and TRP Department of NTUU ‘KPI’, on leaf wood cellulose fiber was researched. The obtained results confirm the fact that these glues give the possibility to receive casts with parameters which overcome of that ones received with the use of Zhukovsky glue, not worse than samples produced with the ceresan glue.
The method of modification of the starch glues on the basis of corn and potato starch was developed. Obtained cationic starch glues of KU – 1, KD – 1 and KU – 2, KD – 2, respectively, were used for making of cardboard samples for the flat layers of corrugated cardboard. It is shown that application of the obtained glues allow to improve the physical-mechanical indexes of cardboard considerably and thus to decrease the turbidity of west water, and also to increase the speed of the de–watering process of pulp on the wire.
4. Антоненко Л.П., Нікітіна Н.В., Остапюк Н.Я., Білан А.Д., Складанний Д.М. Вплив вмісту азоту в модифікованих крохмальних клеях на технологічні показники виробництва тест-лайнеру // Вісник національного технічного університету України «КПІ» Хімічна інженерія, екологія та ресурсозбереження, 2010. – №1(5). - С. 28 – 32.
Метою роботи є дослідження катіонування кукурудзяного крохмального клею азотовмісними сполуками та впливу вмісту азоту в клеях на в’язкість клею, швидкість зневоднення маси на сітці, мутність підсіткових вод і фізико-механічні показники зразків картону з макулатури. Доведено, що ці показники покращуються у разі використання катіонованих крохмальних клеїв.
The purposes of work are modification of the corn starched glue b nitrogen connections and to research the influence of content of nitrogen in glues on the viscidity of glue, on the speed of dehydration of mass on a net, on turbidity of white-water and also on physical-mechanical indexes of cardboard from literary garbage.
5. Шаблий Т.А., Макаренко И.Н., Голтвяницкая Е.В. Разработка эффективной технологии умягчения воды для обеспечения ресурсосбережения в промышленном водопотреблении // Энерготехнологии и ресурсосбережение, 2010. - №1. – С.53 - 58.
The processes of water demineralization with lime, phosphate, fluoride and sodium aluminium hydroxide application are investigated. It is displayed, that phosphate and sodium fluoride are ineffective for water demineralization in doses from 0.5 to 4.0 mg-eq/dm3. They are also ineffective at use in compositions lime at pH 9.0-10.5. It is determined that sodium aluminate provides effective water demineralization but essentially promotes the secondary pollution by aluminium ions. High performance of water demineralization by sodium aluminate with lime composition application is achieved. The residual aluminium concentration in demineralized water ranged between 0.0-6.5 mg/dm3. It is exhibited that magnetite saturated with rigidity ions application increases water clarification and demineralization efficiency.
6. Макаренко І.М., Шаблій Т.О., Носачова Ю.В., Тамазашвілі А.Т. Вилучення іонів міді в процесах іонообмінного пом’якшення води на катіоніті DOWEX MAC-3 // Вісник НТУУ «КПІ»: Хімічна інженерія, екологія та ресурсозбереження, 2010. - №1. – С.53-59.
Приведено результати досліджень по вилученню іонів міді із води в присутності іонів кальцію та магнію. Показано, що слабокислотний катіоніт DOWEX МАС-3 має значну обмінну ємність по іонах жорсткості і по іонах міді, дозволяє вилучати іони міді в присутності іонів жорсткості. Рекомендовано застосовувати двохстадійне катіонування при використанні слабокислотного катіоніту в кислій формі на першій стадії та сильнокислотного катіоніту в Na+-формі на другій стадії.
The results of research on the extraction of copper ions from the water in the presence of calcium and magnesium ions are given. It is shown that the weak-acid cation-exchange resin DOWEX MAC-3 has substantial exchange capacity for ions of water hardness and copper ions and allows extracting copper ions in the presence of ions of water hardness. It is recommended to apply double-stage cationic exchange using the weak-acid cation-exchange resin in the acidic form at the first stage and strong-acid cation-exchange resin in the Na+-form at the second stage.
9. Барбаш В.А., Трембус І.В., Гапон О.С., Шевченко В.М. Одержання солом’яних волокнистих напівфабрикатів пероцтовим способом делігніфікації // Наукові вісті НТУУ «КПІ», 2010. - № 3. - С.42-49.
The paper studies influence of the basic technological parameters of obtaining straw fibrous semi-finished products by the peracetic method of delignification. Using the method of full factorial experiment, we obtain the regression equations of producing straw fibrous semi-finished products. Furthermore, we determine main kinetic characteristics of the delignification process of wheat straw.
10. Барбаш В.А., Трембус І.В., Алєксеєва М.С. Отримання волокнистих напівфабрикатів із нових рослин // Вісник НТУУ «КПІ»: Хімічна інженерія, екологія та ресурсозбереження, 2010. - №1 (5). - С. 79-83.
Досліджено вплив основних технологічних параметрів процесу одержання целюлози із мальви мелюки та сіди багаторічної нейтрально-сульфітним і органосольвентним способами делігніфікації. Визначено фізико-механічні показники одержаних волокнистих напівфабрикатів. Розраховано кінетичні характеристики (константи швидкості та енергії активації) процесу делігніфікації рослинної сировини.
The influence of basic technological parameters of pulping process of malva meluca and sida perennial by neutral sulfite and organosolvent methods of delignification was investigated. Physical-mechanical indexes of obtained pulp were defined. Kinetic characteristics (constants of rate and activation energie) of plant material delignification process were calculated.
11. Іваненко О.І., Отрох О.А. Очищення стічних вод від барвників магніто-сорбційним методом // Вісник НТУУ «КПІ»: Хімічна інженерія, екологія та ресурсозбереження, 2010. - №1 (5). - С. 51-53.
Наведено результати досліджень ефективності видалення барвників дисперсними магнітними частками в залежності від співвідношення концентрацій іонів Fe(ІІ)/Fe(ІІІ) в магнетиті. Визначено залежність сорбційної здатності магнетиту від його концентрації в розчині. Досліджена залежність сорбційних характеристик магнетиту від концентрації барвників. Доведено, що для різних класів барвників умови сорбції їх на магнетиті дещо відрізняються, що пов’язано з різними властивостями барвників та їх будовою.
The results of studies on extraction efficiency of dyes with the usage of dispersive magnetic particles depending on the ratio of Fe(ІІ)/Fe(ІІІ) ions in magnetite are presented. The depending are of the sorption capacity of the magnetite on its concentration in solution has been determined. The affect of a dye concentration on sorption properties of magnetite has been studied. It has been proved, that sorption conditions for various classes of dyes on magnetite are somewhat different, that can be explained by different properties of dyes.
12. Шаблій Т.О., Гомеля М.Д., Панов Є.М. Електрохімічна переробка відпрацьованих розчинів, що утворюються при регенерації катіонітів // Экология и промышленность, 2010. - №2. – С.33 - 38.
Приведено результати досліджень електрохімічної переробки відпрацьованих регенераційних розчинів в двох- та трикамерних електролізерах. Показано, що при переробці кислих розчинів в присутності іонів жорсткості вихід за струмом суттєво знижується. Найвищі виходи за струмом продуктів електролізу (кислоти та лугу) можна досягти при застосуванні трикамерних електролізерів. Рекомендовано повторне використання кислих та лужних розчинів, які утворюються в процесі електролізу.
The results of research on the electrochemical treatment of spent regenerative solutions in the two-and three-chamber electrolyzer are given. It is shown that current efficiency is significantly reduced during the acidic solutions treatment in the presence of the ions of water hardness. The highest current efficiency for the products of electrolysis (acid and alkali) can be achieved when using three-chamber electrolyzers. Reuse of acid and alkaline solutions generated from electrolysis is recommended.
13. Дейкун І.М., Барбаш В.А., Пойда В.В. Одержання мікрокристалічної целюлози із короткого лляного волокна // Вісник Національного технічного університету України «КПІ». Хімічна інженерія, екологія та ресурсозбереження. - 2010. - №1(5). - С.76-79.
Показана можливість делігніфікації короткого лляного волокна варильним розчином пероксиду водню і пероцтової кислоти з використанням каталізаторів. Досліджено процес гідролізу лляної целюлози для виробництва мікрокристалічної целюлози. Вивчено вплив параметрів процесу гідролізу на властивості Мікрокристалічної целюлози.
The possibility of short flax fiber delignification by cooking liquor of hydrogen peroxide and peracetic acid with the application of catalysts is shown. The hydrolyze process of flax cellulose for the microcrystalline cellulose production is investigated. The influence of the parameters of hydrolyze process on microcrystalline properties is studied.
14. Дейкун І.М., Пойда В.В., Барбаш В.А. Використання пероцтової целюлози із соломи ріпаку в композиціях паперу та картону // Упаковка. - 2010. - №3. - С. 13-15.
Показана можливість використання пероцтової ріпакової целюлози в композиції писального паперу та картону для плоских шарів гофрованого картону. Пероцтова целюлоза, одержана з використанням каталізатору молібдату натрію, дозволяє отримати зразки писального паперу з кращими значеннями фізико-механічних показників у порівнянні з целюлозою, що одержана з вольфраматом натрію та змішаним каталізатором. Лабораторні зразки картону, виготовлені з використанням в композиції пероцтової целюлози з соломи ріпаку, мають високі значення фізико-механічних показників.
The possibility of peracetic cellulose application in composition of written paper and cardboard for the flat layers of the corrugated cardboard was shown. Peracetic cellulose obtained with the application of molybdenum catalyst allows to obtain the samples of written paper with better values of physical and mechanical indexes in comparison with pulp which was obtained with vanadium and mixed catalyst. Laboratory samples prepared with the application in composition of peracetic cellulose from rape straw have high values of physical and mechanical indexes.
15. Дейкун І.М., Пойда В.В., Барбаш В.А. Одержання целюлози із соломи ріпаку окисно-органосольвентним способом // Наукові вісті НТУУ «КПІ», 2010. - №2. - С. 143-148.
Досліджено процес варіння целюлози з соломи ріпаку окисно-органосольвентною делігніфікацією. Вивчено вплив основних технологічних параметрів процесу (тривалості, температури, гідромодуля варіння, концентрації пероцтової кислоти і пероксиду водню, виду каталізатору) на вихід та властивості волокнистого напівфабрикату. Встановлено, що використання каталізаторів в процесі варіння соломи ріпаку розчинами пероцтової кислоти дозволяє зменшити вміст лігніну у волокнистому напівфабрикаті. Каталізатор молібдат натрію більш селективно діє на лігнін і не призводить до гідролізу полісахаридів. Одержані математичні залежності, що адекватно описують процес делігніфікації соломи ріпаку пероцтовою кислотою.
The pulping process by the oxidative-organosolvent delignification was investigated. The influence of the basic technological parameters of process (duration, temperature, liquor/raw material ratio, concentration of peracetic acid and hydrogen peroxide, type of catalyst) on pulp yield and properties of pulp was studied. It was found out that application of catalysts in the process of rape straw cooking with the liquors of peracetic acid allow to reduce lignin content in pulp. Molybdenum catalyst acts more selectively on lignin and does not promote hydrolyze of polissaharides. Mathematical dependences which adequate described the delignification process of rape straw with peracetic acid were obtained.
16. Дейкун І.М., Пойда В.В., Барбаш В.А.Дослідження паперотворних властивостей пероцтової целюлози із соломи ріпаку // Упаковка, 2010. - №2. - С. 32-34.
Досліджена мікроскопічна будова соломи ріпаку та пероцтової целюлози, одержаної варінням соломи ріпаку розчином пероцтової кислоти. Визначено фракційний склад за довжиною волокна пероцтової целюлози із соломи ріпаку. Встановлено, що пероцтова целюлоза з соломи ріпаку володіє високими показниками міцності, що близькі до показників целюлози сульфатної вибіленої з листяної деревини.
Microscopic structure of rape straw and peracetic cellulose obtained from rape straw by cooking with the liquor of peracetic acid were investigated. Fractional content on fiber length of peracetic cellulose from rape straw was defined It was found out the peracetic cellulose from rape straw has high indices of durability that near to indices of sulfate bleached cellulose from leafy wood.
17. Khokhotva O., Waara S. The influence of dissolved organic carbon on sorption of heavy metals on urea-modified pine bark // Journal of Hazardous Materials, 2010. - №173. – Р. 689–696.
A previous study showed considerably higher metal adsorption by urea-treated pine bark (UTB) compared to non-treated bark (NTB) at metal adsorption from their individual relatively concentrated solutions. Comparison of the sorption characteristics of the two pine barks at low but environmentally relevant metal concentrations, and investigation of the influence of pH and dissolved organic carbon (DOC) on the sorption process are the aims of the present study. Sorption of Cu2+, Ni2+, Zn2+ and Pb2+ on pine bark of the species Pinus sylvestris was measured in multi-metal solutions in the presence and absence of DOC. In the absence of DOC, UTB gave lower residual metal concentrations (2-7 μg/l for copper, 1-5 μg/l for nickel, < 0.05 μg/l for zinc and lead) in the range of initial concentrations up to 0.7 mg/l, compared to NTB (6-15 μg/l for copper, 2-24 μg/l for nickel, 2-9 μg/l for zinc, 2-3 μg/l for lead). In the presence of DOC, sorption of Zn, Ni and Pb decreased by up to 75% depending on the DOC concentration. Metal sorption on UTB is less sensitive to pH and more adsorbed metal ions are retained compared to NTB. The potential use of urea-treated bark for treatment of wastewater containing DOC and low concentrations of metals is discussed.
Попередні дослідження показали, що соснова кора, модифікована розчином карбаміду сорбує суттєво більшу кількість важких металів з індивідуальних відносно концентрованих розчинів. Метою даної роботи є порівняння сорбційних характеристик двох зразків соснової кори при низьких, але екологічно значимих концентраціях металів, і дослідження впливу рН та розчиненого органічного вуглецю (РОВ) на процес сорбції. Адсорбція Cu2+, Ni2+, Zn2+ і Pb2+ сосновою корою виду Pinus sylvestris визначалася із розчину суміші металів у присутності та відсутності РОВ. У відсутності РОВ з корою, модифікованою карбамідом, досягається нижча залишкова концентрація металів (2-7 мкг/л міді, 1-5 мкг/л нікелю, < 0,05 мкг/л цинку і свинцю), ніж у разі використання немодифікованої кори (6-15 мкг/л міді, 2-24 мкг/л нікелю, 2-9 мкг/л цинку і 2-3 мкг/л свинцю) при сорбції з розчинів з початковою концентрацією до 0,7 мг/л. У присутності РОВ сорбція Zn, Ni і Pb падає до 75%, залежно від концентрації РОВ. Сорбція металів на модифікованій корі менш чутлива до рН і утримує більшу кількість металів. Обговорено потенційні можливості використання кори, модифікованої карбамідом, для очистки стічних вод, які містять РОВ і низькі концентрації металів.
18. Носачова Ю.В., Зеленюк О.С., Гомеля М.Д. Очищення січних вод від сульфат-іонів за допомогою вапна та алюмінієвого коагулянту // Вісник НТУУ «КПІ» Хімічна інженерія, екологія та ресурсозбереження. – 2010. - №1(5). – С.48-50.
Приведені результати експерименту по очистці стічних вод, які містять велику кількість сульфат-іонів з використанням вапна та алюмінієвого коагулянту, визначені оптимальні параметри та дози реагентів для проведення процесу. Показано, що при глибокому ступені очищення від сульфат-іонів не cпостерігається вторинного забруднення іонами кальцію та алюмінію.
Results of experiment of sewage treatment which contain abundance of sulfate ions with usage lime and aluminium coagulant are shown. Defined optimal parameters and doses for advancing of process. With deep purification rate from sulfate ions not observe dirtying of calcium ions and aluminium ions are shown.
19. Михайловська М.В., Радовенчик Я.В., Черниш О.М. Очищення стічних вод від сульфат – іонів // Вісник НТУУ «КПІ» Хімічна інженерія, екологія та ресурсозбереження. – 2010. - №1(5). – С.59-63.
Досліджено можливості реагентного видалення із природних та стічних вод сульфат-іонів для доведення їх вмісту до рівнів, котрі нижче граничних норм на скид в каналізацію та поверхневі водойми. Вивчено ефективність осадження сульфат-іонів у вигляді сульфату кальцію та сульфату барію, вплив на процес осадження різних факторів, оцінено можливість використання різних осаджувачів в реальних технологічних процесах.
Possibilities of the reagentnogo deleting are explored from natural and sewers waters of sul'fat-ionov for taking of their concentrations to the levels which below than maximum norms on an upcast in the sewage system and superficial reservoirs. Efficiency of besieging of sul'fat-ionov is studied as a sulfate of calcium and sulfate of barium, influence on the process of besieging of different factors, possibility of the use
of different osaditeley is appraised in the real technological processes.
20. Радовенчик Я.В., Котлярова В.С. Вивчення умов перетікання рідини в капілярних матеріалах // Восточно- Европейский журнал передовых технологий, 2010. - №48. – С. 23-25.
Наведено результати експериментів та теоретичних розрахунків основних параметрів процесу перетікання рідини по матеріалах з капілярними властивостями.
Experimental results and theoretical calculations of the basic parameters for the process of fluid flowing through the materials with capillary characters were presented.
21. Трембус І.В., Барбаш В.А. Отримання солом’яних волокнистих напівфабрикатів органо-сольвентними способами делігніфікації // Наукові праці студентів і аспірантів – переможців щорічних конкурсів на здобуття фінансової підтримки НТУУ для виконання науково-дослідних робіт. К.: НТУУ «КПІ», 2010. - С.78-81.
22. Іващенко Г.В., Вембер В.В., Грузіна Т.Г., Рєзніченко Л.С., Ульберг З.Р. Інтенсивність процесів пероксидного окислення ліпідів як системний біомаркер біобезпечності наночастинок металів // Український біохімічний журнал. – 2010. – Т. 82, № 4. – С. 254.
25. Плосконос В.Г., Черьопкіна Р.І. Оптимізація композиційного складу волокнистих напівфабрикатів для виготовлення паперу для гофрування // Упаковка, 2010. - №2. - С. 28-31.
28. Хохотва О.П., Аветісян Ю.І., Дегтярьова А.В., Соснова тирса: дослідження фізико-хімічних характеристик сорбента / Вісник Національного технічного університету України "Київський політехнічний інститут", Хімічна інженерія, екологія та ресурсозбереження, 2014. - № 1. - С. 93-96.
Робота присвячена визначенню фізико-хімічних властивостей поверхні сорбента (питомої площі поверхні, питомої густини кислотних та основних активних центрів), оскільки ці параметри є визначальними для ефективного вилучення забруднюючих речовин. Об’єктом дослідження була немодифікована та оброблена розчином карбаміду соснова тирса. Внаслідок обробки карбамідом, питома площа поверхні тирси зросла на 35 %. Кислотно-основним титруванням з подальшою математичною обробкою отриманих даних було встановлено, що кількість поверхневих карбоксильних груп зменшилася, кількість лактонних груп не змінилася, однак відносна кількість фенольних груп значно зросла, з’явилися основні групи, які є додатковим активним центрами сорбції важких металів.
The main goal of the paper was to determine physicochemical properties of sorbents surface (specific surface area, the specific density of the acid and alkaline active centers) as they pay significant role in effectiveness of water treatment process. The non-modified and modified by carbamide solution pine sawdust were the objects of the study. As a result of treatment by carbamide, the specific surface area increased at 35%. It was investigated by the acid-base titration followed by mathematical processing that quantity of surface carboxylic groups decreased, the quantity of lactonic groups were constant, while relative concentration of phenolic groups increased and basic groups, which are the active centres of sorption of heavy metals, appeared.
29. Хохотва О.П., Аветісян Ю.І. Видалення з води іонів міді модифікованим феритним сорбентом // Проблеми водопостачання, водовідведення та гідравліки. Науково-технічний збірник. Київський національний університет будівництва і архітектури, 2014. - випуск 23. - С. 133-136.
Проведено дослідження сорбції Cu2+ з розчинів концентрації 50 мг/л в присутності іонів кальцію в концентраціях до 400 мг/л, немодифікованим та модифікованим 2% розчином тіокарбаміда форомагнетиком. Отримані результати показали, що модифікований форомагнетик забезпечує більш глибоке очищення та знижує чутливість процесу до солей жорсткості.
The sorption of Cu2+ from the solutions with concentration 50 mg/l with the presence of calcium ions in concentration up to 400 mg1 on non-modified and modified by 2% solution of tiocarbamide ferromagnetics were studied The results showed the modified ferromagnetic provides deeper purification and reduces sensitivity of process towards hardness salts.
30. Гомеля Н.Д. Очистка воды от сульфатов известкованием при добавлении реагентов, содержащих алюминий / Н.Д. Гомеля, И.Н. Трус, Ю.В. Носачева // Химия и технология воды. – 2014. – № 2. – С. 129-137.
Изучены процессы очистки воды от сульфатов при обработке известью, алюминатом натрия или гидроксидом алюминия. Показано, что эффективность извлечения сульфатов зависит от типа и расхода реагентов, содержащих алюминий, от способа предварительной обработки гидроксида алюминия. Определено влияние последующей обработки воды углекислотой или магнезитом на эффективность очистки воды от сульфатов, на степень её умягчения и остаточную щелочность.
The article has investigated the processes of water purification of sulfates when treating with lime, sodium aluminate or aluminum hydroxide. It has been shown that the efficiency of removing sulfates depends on the type and consumption of reagents containing aluminum and the method of pretreating aluminum hydroxide. The paper has determined the effect of after treatment by carbon dioxide or magnesite on the efficiency of water purification of sulfates, the degree of its softening, and residual alkalinity.
31. Гомеля М. Д. Вплив аерації та електролізу на зниження вмісту заліза / М. Д. Гомеля, І. М. Трус, В. М. Грабітченко // Екологічна безпека. – 2014. – № 1 (17). – С. 78-82.
The forms of existence of iron in natural waters and methods of deferrization are analysed. Application of method of the simplified aeration is well-proven for the decrease of content of iron in water. Experiments were held at room temperature with using microcompressor for water aeration. On the basis of this experiments was established that at initial iron concentration of 0,65 mg/dm3 for initial iron content in the water less then 0,3 mg/dm3 enough initial aeration during 1-5 min. By increasing of iron concentration at outgoing water to 7,0 mg/dm3 aeration during 10 min permits decrease remaining iron content to 0,52 mg/dm3, at standard not over 0,3 mg/dm3. The removal of iron from water was investigated during electrolysis. The iron removal process was conducted in the electrolizer with different iron concentration. . In this work was used single-stage electrolyser, as cathode was used alloy steel plate and as anode was used titanium plate, which was covered by ruthenium oxide. Was established that acceptable iron concentration in water can be achieved at electrolysis time of 1 and 3 min for iron content in outgoing water 0,65 and 7,00 mg/dm3 accordant, at that water treatment level from iron composed 77-88% and 90-100% accordant. The received results testify to expediency of application of electrochemical methods of clearing of water and can be used for development of industrial devices.
32. Gomelya M.D. Application of aluminium coagulants for the removal of sulphate from mine water // M.D. Gomelya , I.M. Trus, T.O. Shabliy // Chemistry & Chemical Technology. – 2014. – 8 (2). – P. 197-203.
The results of treatment of solutions with high sulphates concentration and the high rate of water hardness are given. It is shown that the significant reduction of secondary pollution by chlorides achieved through an integrated use of aluminium hydroxchloride and sodium aluminate coagulants. It was found that the efficiency of water purification of sulphates and water softening can be increased with the carbon dioxide processing.
33. Макаренко І.М. Іонообмінне знесолення та пом’якшення вод із підвищеними рівнями мінералізації та жорсткості / І.М. Макаренко, І.М. Трус, В.М. Грабітченко // Праці Одеського політехнічного університету. – 2014. – № 1 (43) . – С. 235-241.
This work lies in the range of science topics on creation of low-waste demineralization technology of light-salted natural and waste water. The aim of this work is to study the sorption processes of chlorides and sulfates on anion exchange resin AV-17-8 in basic form for development effective way of water mitigation and demineralization without using cation exchange resin. Scientific novelty of such method is to determine the dependence of ionic water constitution, ion exchange form and conditions of its regeneration on the efficiency of mitigation and demineralization of water with high level of sulfates, chlorides and hardness. Ion exchange method of water treatment based on the use of high-basic anion exchange resin in OH- form in dynamic conditions. Practical importance of this research is to develop a convenient method for treatment of mine water and concentrates from baromembrane desalination of water that provide a creation of low-waste demineralization processes of water with high salinity.
34. Гомеля М.Д. Оцінка ефективності зворотньоосмотичного опріснення води після її пом’якшення на слабокислотному катіоніті / М.Д Гомеля., І.М. Трус, В.М. Радовенчик // Вісник Вінницького політехнічного інституту. – 2014. – № 3. – С. 32-36.
The evaluation of the efficiency of the low-mineralized water desalination at reverse osmosis membranes Filmtec TW 30-1812-50 depending on the water characteristics was performed. The influence of stabilizing treatment on the weak acid cation exchange resin in the acid form was determined on the basis of membrane characteristics. It is shown that acidification of water during the processing on the weak acid cation exchange resin reduces the membrane selectivity for chlorides while the selectivity for sulfate and water hardness ions remains high. During weak acid solutions treatment on the membrane the pH level in concentrate and permeate is approximately equal, while filtering the original model solution rises pH level in the concentrate to 9, and in permeate reduces to 7, due to the lower membrane selectivity for hydrocarbonate, compared with the water hardness ions.
37. Гомеля М.Д. Нанофільтраційне опріснення слабомінералізованих вод / М. Д. Гомеля, І. М. Трус, В. М. Грабітченко // Вопросы химии и химической технологии. – 2014. – № 1. – С. 98-102. The processes of membrane treatment of mine waters that contain sulfates, chlorides and water hardness ions are explored. It is shown that in case of relatively low concentrations of chlorides (100-200 mg/dm3) use of nanofiltration provides effective desalting. Simultaneously water treatment from sulphate and water hardness ions occurs. This provided a high quality of permeate and made demineralization of concentrates by reagent method of lime processing with using of high-basic aluminum coagulants possible. 38. Трус І.М. Переробка осадів, що утворюються при реагентному очищенні шахтних вод від сульфатів / Трус І.М., Флейшер Г.Ю., Гомеля М.Д., Токарчук В.В. // Вісник КрНУ. – 2014. – № 4. – C. 169-174. During developing of coal bed on 1 of produced coal accounts for 3 m3 of water, so the problem of waste disposal and treatment of mine water is very important and urgent problem and needs to be resolved. In this paper presents the results of research of mine water treatment by reagent method with using aluminic coagulants and described the methods of tankage disposal which obtained in the construction industry. Studied the process water treatment from sulfates while processing of lime, 2/3 hydroxochloride aluminum or sodium aluminate. Is defined the influence of water treatment with using magnesite on the effectiveness of water treatment from sulfates and effectiveness of softening. It is shown that a high degree of water treatment from sulfates and its softening is achieved by using lime, sodium hydroxoaluminate and magnesite. Reagent method based on the deposition of calcium sulfohidxoaluminate – 3СаО•Al2O3•3CaSO4•31H2O, because these sediments are similar to one of the cement hydration products – ettringite, so they should be disposed of in the construction industry. It is found that this residue after water softening process could be used as a partial cement replacement, an admixture accelerating blended cement hardening and as an expansive admixture for shrinkage compensating cements and concretes. 39. Гомеля М.Д. Електродіалізне опріснення розчинів з високим вмістом іонів жорсткості / М.Д. Гомеля, І. М. Трус, Т.О. Шаблій // Вісник ЧДТУ. – 2014. – № 1 (71). – С. 50-55. Processes of electrodialysis in desalting concentrated high-hardness salt solutions were studied. Electrodialysis was conducted in three-chambered electrolyzer with two anionite membranes MA-41. It is shown that speed of the process and faraday efficiency rise with the increase of ion concentration in the solution. Alkali concentration in cathode region has no influence on the process effectiveness. It is proved that magnesit adding into the high-hardness solution, when performing electrodialysis, contribute to effective water softening. 40. Ammonia-sulfite-ethanol pulp from wheat straw / Valerii Barbash, Irina Trembus, Valentina Shevchenko // Cellulose chemistry and technology, 2014, №48, 3-4 march-april, p. 345-353. The results of obtaining straw pulp by ammonia-sulphite-alcohol (ASA) and alkali-sulphite-alcohol (ASAE) methods were presented. Influence of main technological parameters on quality of straw pulp obtained by organosolvent method was investigated. Positive influence of anthraquinone on the process of organosolvent delignification of wheat straw was researched. Possibility of bleaching organosolvent straw pulp by reagents that don’t include chlorine was researched. Indexes of selectivity of removing lignin from wheat straw by different organosolvent methods were calculated and compared. It was shown that ASAE and ASA methods of pulping wheat straw have higher degrees of selectivity and delignification. Представлено результати одержання солом’яних волокнистих напівфабрикатів аміачно-сульфітно-спиртовим (АСС) та лужно-сульфітно-спиртовим (ASAE) способами. Досліджено вплив основних технологічних параметрів на показники якості одержаних органосольвентних соломяних волокнистих напівфабрикатів. Показано позитивний вплив антрахінону на процесс органосольвентної делігніфікації пшеничної соломи. Вивчено можливість вибілювання органосольвентних солом’яних целюлоз реагентами, що не містять хлор. Розраховано і порівняно показники вибірковості видалення лігніну із пшеничної соломи різними органосольвентними способами. Показано, що більший ступінь селективності та ступінь делігніфікації мають ASAE і ACC способи варіння пшеничної соломи. 41. Лужно-сульфітно-спиртова делігніфікація стебел соняш-нику і свербіги / Барбаш В.А., Трембус І.В., Плосконос В.Г., Швидкий А.М. // Вісник НТУУ «КПІ» Хімічна інженерія, екологія та ресурсозбереження, 2014, №1, с. 80-84. Досліджено вплив основних технологічних параметрів процесу лужно-сульфітно-спиртової делігніфікації стебел соняшнику і свербіги на показники якості волокнистих напівфабрикатів. Розраховано показники вибірковості видалення лігніну із стебел рослинної сировини дослідженим способами делігніфікації. Отримано математичні залежності показників якості волокнистих напівфабрикатів від основних технологічних параметрів з використанням методу групового урахування аргументів. The influence of the main technological parameters of the alkaline sulfite-alcohol delignification of sunflower and bunia stems on quality indexes of pulp. Selectivity indexes of lignin removal from the plant by studied method of delignification were calculated. The mathematical dependencies of pulp quality indexes on the main technological parameters using the method of arguments group consideration. 42. Гомеля М.Д. Фільтрувальний матеріал для баромембранного очищення води / М.Д. Гомеля, О.М. Мовчанюк // Вісник НТУУ "КПІ". Серія "Хімічна інженерія, екологія та ресурсозбереження". – 2014. – 1(12). – С. 45 – 51. Стаття присвячена отриманню з сульфатної хвойної вибіленої целюлози фільтрувального матеріалу для очищення води від зважених та колоїдних часток, що обумовлюють її каламутність. Досліджено вплив вмісту лавсанового волокна та клею на основі полівінілового спирту на механічні та експлуатаційні характеристики фільтрувального матеріалу. Receiving from the sulfate coniferous bleached cellulose of filtration material for water treatment from the self-weighted and colloid parts which stipulate its lees was represented in this article. Influence of content of lavsan fibre and to glue on the basis of polyvinyl alcohol on mechanical and operating descriptions of filtration material was investigated. 43. Дейкун І. М., Барбаш В. А. Вплив вибілювальних реагентів на якість лляної целюлози / Вісник Національного технічного університету України «КПІ». Хімічна інженерія, екологія та ресурсозбереження. Науковий збірник.- 2014.-№1(12).- С.84-87. The effect of bleaching chemicals – chlorine dioxide, hydrogen peroxide and chlorine – on the product yield, residual lignin content, cellulose, viscosity, whiteness and ash of flax cellulose for chemical processing is studied. 45. Барбаш В.А., Нагорна Ю.А. Вплив попередньої обробки волокон льону на показники целюлози / Східно-Європейський журнал передових технологій, 2014, №4/6 (70), С. 4- 8. Досліджено процес лужної та кислотної обробки на показники якості лляних волокнистих напівфабрикатів. Визначено оптимальні умови проведення лужної та кислотної обробки волокон льону. Встановлено, що обробка волокон льону у лужному і кислому середовищі видаляє лігнін і мінеральні речовини з волокон льону та рекомендується для використання у виробництві мікрокристалічної целюлози. Influence of main technological parameters (temperature, duration, liquid-to-solid ratio, catalyst content) of alkali and acid treatment of flax fibers on quality indices of obtained pulps was investigated. Impact of different chemical reagents on removal of non-cellulose components from flax fibers, in particular mineral compounds, was studied. It was established that during alkali treatment of flax fibers sodium hydroxide removes lignin and mineral compounds better than potassium hydroxide and ammonia aqueous solution. 47. Барбаш В.А., Нагорна Ю.М. Вплив стадій обробки волокон луб’яних культур на показники мікрокристалічної целюлози / Наукові вісті НТУУ «КПІ», 2014, № 2, с. 117-120. Досліджено процес одержання мікрокристалічної целюлози із волокон недеревної рослинної сировини (льону, конопель, кенафу) з використанням кислотного передгідролізу, лужно-сульфітно-спиртового способу делігніфікації та окислювально-органосольвентної обробки. Встановлено, що проведення кислотного передгідролізу на першій стадії одержання мікрокристалічної целюлози дозволяє значно зменшити вміст мінеральних речовин (на 62-75 %), частково вихід волокнистого напівфабрикату (на 9-12 %) і вміст залишкового лігніну (на 20-30 %) у порівнянні з вихідною сировиною. Проведення органосольвентної делігніфікації зменшує до 1% вміст залишкового лігніну у целюлозах з усіх досліджених волокон. Скорочено кількість стадій технологічного процесу одержання мікрокристалічної целюлози за рахунок об’єднання процесів вибілювання та гідролізу органосольвентної целюлози із волокон луб’яних культур з використанням суміші розчинів оцтової кислоти та пероксиду водню концентрацією 35 % і 30 %, відповідно. Одержана мікрокристалічна целюлоза із волокон луб’яних рослин відповідає вимогам стандарту і рекомендується для використання на фармацевтичних підприємствах в якості наповнювача для виготовлення лікарських пігулок. The process of obtaining microcrystalline cellulose from non-wood plant bast fibers (flax, hemp, kenaf) using preliminary acid hydrolysis, alkaline sulfite -alcohol method of delignification and oxidation-organosolvent processing was investigated. It is established that the carrying out of preliminary acid hydrolysis in the first step of obtaining microcrystalline cellulose can significantly reduce the mineral content (on 62-75 %), partly yield of pulp (on 9-12 %) and residual lignin content (on 20-30 %) relatively to raw material. Carrying out of organosolvent delignification reduces content of residual lignin to 1% in the pulp of all studied fibers. The number of stages of obtaining microcrystalline cellulose technological process was reduced. It was achieved by combining the processes of bleaching and hydrolysis of organosolvent cellulose from plant bast fibers using a mixture of acetic acid and hydrogen peroxide with concentrations of 35 % and 30 %, respectively. The resulting microcrystalline cellulose from plant bast fibers meets the standard and it is recommended for applications in pharmaceutical companies as a filler for the medical tablets production. 48. Антоненко Л.П., Івашкевич О.О., Плосконос В.Г. Вплив вмісту азоту в крохмальних клеях на показники якості флютінгу / Вісник НТУУ«КПІ» Хімічна інженерія, екологія та ресурсозбереження. Науковий збірник №1 (11) – 2013. - с. 68 – 73. Встановлено, що із збільшенням вмісту азоту в крохмальному клеї, катіонованому диметиламіном, він краще утримується на волокні, що в свою чергу призводить до зменшення вмісту крохмалю в підсітковій воді та мутності підсіткових вод і до покращення фізико-механічних показників паперу для гофрування в 2 і більше рази. Встановлено, що доцільно використовувати крохмальний клей модифікований диметиламіном з вмістом азоту понад 1,5 %. Зроблено порівняння показників якості флютінгу та підсіткових вод, які утворились під час виготовлення паперу за різного місця введення клею (введення клею під час розмелювання, введення клею під час відливання та введення 50 % клею під час розмелювання і 50 % під час відливання). Встановлено, що найкращі показники мають зразки флютінгу виготовлені за умови введення крохмального клею, катіонованогодиметиламіном з вмістом азоту 2 %, під час відливання. За експериментальними даними виконане математичне оброблення результатів. Математичні моделі, які одержані за методом самоорганізації складних систем на базі групового врахування аргументів, адекватно описують досліджувані процеси. It is proved that with the increase of nitrogen content in starch adhesives, cationated by dimetilamin, he is better kept on the fiber, which in turn leads to both decrease in the starch content and turbidity of the subgrid water and increase physical and chemical characteristics of the paper for goffering more than two times. It is proved that expedient to use starch adhesiv, cationated by dimetilamin with nitrogen content more then 1,5 %.It is spend comparison of indicators of quality fluting and subgrid water which was reception at manufacturing of a paper incase of a different place of introduction of glue (at adition glue in time drinding, in time outflow and 50 % glue in time drinding and 50 % in time outflow).It is established that the best indicators samples fluting made of introductions tarch glue, cationated by dimetilamin with them aintenance of nitrogen have of 2 %, duringtime outflow. From experimental data mathematical treatment of results is done. The got mathematical models which was got on the method of organization of the difficult systems on the basis of group account of arguments, describe probed process adequately.
For microcrystalline cellulose production from flax fibers, it is recommended to perform alkali treatment with the concentration of sodium hydroxide 20-25 %, temperature 160 0С and duration 180 minutes. A preliminary acid hydrolysis stage of flax fiber is recommended to perform by sulfuric acid 1 % solution, temperature 100 0С and duration 180 minutes.